Klaida
-
- Klubo remėjas
- Posts: 79
- Joined: 2015 01 13 , 19:59
- Vardas/Pavardė:: aurimas
- Lytis: Vyras
- Mondeo karta: MkIII
- Kuro tipas: Dyzelinas
- Kėbulo tipas: Sedanas
- Spalva: Mėlyna
- Vairuoja nuo: 2007
- Location: telsiai
- Contact:
Klaida
Sveiki, diagnostikoj rasta klaida p1631, gal kam teko su ja susidurt? Mk3, tddi 85kw
-
- Dalyvis
- Posts: 441
- Joined: 2015 11 08 , 11:02
- Vardas/Pavardė:: Vaidas
- Lytis: Vyras
- Mondeo karta: MkIII
- Variklis: 2,0 l Duratec
- Kuro tipas: Dyzelinas
- Kėbulo tipas: Universalas
- Spalva: Mėlyna
- Location: Molėtai
- Contact:
Re: Klaida
Šita klaida tau sukelia kokius tai nors šalutinius simptomus ar tik radot klaidą diagnostikoj?
P1631 Main Relay (power hold) - "This code (P1631) refers to the power hold relay for the engine management system. If there is a permanent concern with this relay then the engine would normally cut out or fail to start. Nine times out of ten the code is set in error normally due to the ignition been cycled a couple of time in quick succession. The relay is located in the fuse box next to the battery and is numbered K163 in the diagram.
The relay is triggered by the engine management, pins 5 and 2 are 12 volt feeds, pin 1 is the switched wire operated by the engine management to energize the relay and pin 3 is the 12 volt feed to various engine management components when the relay is energized, these components include the EGR actuator, the vehicle speed sensor if equipped and the variable vane turbo actuator".
K163 - Apžiūrėk šitą rėlę, esančia saugiklių bloke po vairu:
P1631 Main Relay (power hold) - "This code (P1631) refers to the power hold relay for the engine management system. If there is a permanent concern with this relay then the engine would normally cut out or fail to start. Nine times out of ten the code is set in error normally due to the ignition been cycled a couple of time in quick succession. The relay is located in the fuse box next to the battery and is numbered K163 in the diagram.
The relay is triggered by the engine management, pins 5 and 2 are 12 volt feeds, pin 1 is the switched wire operated by the engine management to energize the relay and pin 3 is the 12 volt feed to various engine management components when the relay is energized, these components include the EGR actuator, the vehicle speed sensor if equipped and the variable vane turbo actuator".
K163 - Apžiūrėk šitą rėlę, esančia saugiklių bloke po vairu:
-
- Klubo remėjas
- Posts: 79
- Joined: 2015 01 13 , 19:59
- Vardas/Pavardė:: aurimas
- Lytis: Vyras
- Mondeo karta: MkIII
- Kuro tipas: Dyzelinas
- Kėbulo tipas: Sedanas
- Spalva: Mėlyna
- Vairuoja nuo: 2007
- Location: telsiai
- Contact:
Re: Klaida
Siaip su trauka kartais bun geresne, kartais prastesne. Dabar po klaidos istrinimo trauka atrodo geresne. Ryt nuvaziuosiu i kaima ir paziuresiu ta rele. Aciu tau
Who is online
Users browsing this forum: No registered users and 3 guests